flashpro4 usb下载线类目 > 商铺首页 > 产品展示 > 深圳市下载线厂家_flashpro4 usb下载线

flashpro4 usb下载线

[Microsemi

flashpro4]

深圳市下载线厂家

价格： 电议

物流： 广东深圳市福田区| 卖家支付运费

可销售总量： 99件

手机： 13823138950 邮箱： mrlei13823138950@163.com

传真： 尚未完善 地址： 广东深圳市

在线询盘联系厂家：13823138950 0755-83244576

在线询盘

提交询盘信息，一呼百应会为您匹配更多优质、合适的供应商！

*采购产品：

信息不能为空！请填写！

*采购量/单位：

采购量不能为空！

*期望价格：

元

价格不能为空！

*报价截止日期：

截止日期不能为空！

*联系人：

联系人不能为空！

*联系电话：

联系电话不能为空！

[Microsemi flashpro4]

我想要了解：

产品价格更多商品信息

请输入您要咨询的问题：

您的联系方式：

邮箱：

手机：

详细信息（flashpro4 usb下载线）

品牌： Microsemi
型号： flashpro4 usb下载线
类型： 仿真器
用途： 军工
功率： 3.3
批号： 16+

FlashPro4 Device Programmer

Quickstart Card

This quickstart card applies only to the FlashPro4 device programmer.

Kit Contents

Quantity	Description

1	FlashPro4 programmer standalone unit

1	USB A to mini-B USB cable

1	FlashPro4 10-pin ribbon cable

Software Installation

If you are already using Actel's Libero? Integrated Design Environment (IDE), you have the FlashPro software installed as part of Libero IDE. If you are using the FlashPro4 device programmer for standalone programming or on a dedicated machine, download and install the latest release of the FlashPro software from the Actel website. The installation will guide you through the setup. Complete the software installation before connecting the FlashPro4 device programmer to your PC.

Note: Libero IDE v8.6 SP1 or FlashPro v8.6 SP1 are the minimum versions required to run FlashPro4.

Software releases: www.actel.com/download/program_debug/flashpro.

Hardware Installation

After installing the software successfully, connect one end of the USB cable to the FlashPro4 device programmer and the other end to your PC’s USB port. The Found Hardware Wizard will open twice. Use the wizard to install the driver automatically (recommended). If the Found Hardware Wizard cannot find the drivers automatically, then ensure you have properly installed the FlashPro software prior to installing the hardware. If the drivers still cannot be installed automatically, then install them from a list or specific location (advanced).

If FlashPro was installed as part of the Libero IDE default installation, the drivers are located at C:/Libero/Designer/Drivers/Manual. For a standalone FlashPro default installation, the drivers are located at C:/Actel/FlashPro/Drivers/Manual. Actel recommends the automatic driver installation.

FlashPro4 Device Programmer Quickstart Card

Note: FlashPro4 uses pin 4 of the JTAG connector whereas FlashPro3 had no connection to this pin. FlashPro4 pin 4 of the JTAG header is a PROG_MODE output drive signal. PROG_MODE toggles between programming and normal operation. The PROG_MODE signal is intended to drive an N or P Channel MOSFET to cool the output of a voltage regulator between the programming voltage of 1.5 V and normal operation voltage of 1.2 V. This is required for ProASIC^?3L, IGLOO^? V2, and IGLOO PLUS V2 devices because, although they can operate at 1.2 V, they must be programmed with a VCC core voltage of 1.5 V. Please refer to FlashPro4 Backward Compatibility with FlashPro3 and Using FlashPro4 PROG_MODE for 1.5 V Programming of ProASIC3L, IGLOOV2, and IGLOO PLUS V2 Devices for more information.

TCK	1	2	GND
TDO	3	4	PROG_MODE
TMS	5	6	VJTAG
VPUMP	7	8	TRST
	9	10	GND

Pin 4 on FlashPro4 programmers MUST NOT be connected or used for anything other than its intended pure.

Common Issues

If the On LED does not light up after FlashPro4 driver installation, the driver might not be installed correctly and you must troubleshoot the installation. For more information, refer to the FlashPro Software and Hardware Installation Guide and the “Known Issues and Workarounds” section of the FlashPro software release notes: www.actel.com/download/program_debug/flashpro.

FlashPro4 may not operate correctly if pin 4 of the JTAG connector is improperly used. See the above note.

Documentation Resources

Refer to the FlashPro software page for further information:

www.actel.com/products/hardware/program_debug/flashpro.

Technical Support and Contacts

Technical support is ailable online at www.actel.com/support, by email at tech@actel.com, or by phone:

Phone (NA): 800.262.1060

Phone (Int'l): +1 650.318.4460

Actel Sales offices, including Representatives and Distributors, are located worldwide. To find your local representative go to: www.actel.com/company/contact.

***************************************************

联系人 ;雷俊（先生）

深圳博瑞图电子科技有限公司

TEL:0755-36675904

MOB:13823138950

FAX:0755-83244576

ADD:深圳市福田区中航路世纪汇都会轩1416室

EMAIL: 401512450@qq.com

网址：www.szprotools.com

***************************************************

承接销售元器件IC一条龙、专注10年

标签： Micr flas Microsemi flashpro4 深圳市下载线深圳市下载线厂家