Model
| TDS1202S
| TDS1122S
| TDS1062S
|
Oscilloscope mode
|
Bandwidth
| 200MHz
| 120MHz
| 60MHz
|
Real-time Sample Rate
| 1GSa/s
|
Equivalent Sample Rate
| 25GSa/s
|
SEC/DIV Range
| 2nS/div-2000S/div (in a 2, 4, 8 sequence)
|
Delay Time Accuracy
| 500ps
|
Vertical
|
A/D Converter
| 8-bit resolution
|
VOLTS/DIV Range
| 2mV/div～5V/div at input BNC
|
ition Range
| ±50V(5V/div),±40V(2V/div～500mV/div), ±2V(200mV/div～50mV/div)±400mV(20mV/div～2mV/div)
|
Record Length
| Single-channel: Maximum 2M; Dual-channel:Maximum 1M
|
Trigger
|
Trigger Sensitivity
(Edge Trigger Type)
| DC: CH1/CH2(Typical) 1div from DC to 10MHz;1.5div from 10MHz to Full
AC: Attenuates signals below 10Hz
HF Reject: Attenuates signals above 80kHz
LF Reject: Attenuates signals below 150kHz
Noise Reject: Reduces trigger sensitivity
|
Trigger Level Range
| CH1,CH2: ±8 divisions from center of screen
|
Trigger Level Accuracy,
typical (Accuracy is for signals hing rise and fall times ≥20ns)
| CH1,CH2: ±(0.3div×V/div) (within ±4 divisions from center of screen)
|
Holdoff Range
| 100ns-10s
|
Trigger Type
|
Edge
| Trigger on the rising or falling edge
|
Pulse Width
| Trigger (when >,<,=,≠) on positive or negative pulses
Pulse Width Range: 20ns-10s
|
Video
| Trigger on an NTSC, PAL, or SECAM standard video signal
Line Range: 1-525 (NTSC), 1-625 (PAL/SECAM)
|
Slope
| Trigger (when >,<,=,≠) on a positive or negative slope
Set Time: 20ns–10s
|
Overtime
| from the rising or falling edge
Set Time: 20ns-10s
|
Alternate
| Internal trigger on edge, pulse width, video or slope
|
Measurement
|
Cursors
| Manual: The difference between voltage cursors △V; the difference between time cursors △T; 1/△T calculated by Hz.
Tracing: The voltage and time at a weform point
|
Automatic
| Pk-Pk, Max, Min, Mean, Cyc RMS, Frequency, Period, Rise Time, Fall Time, positive Width, Negative Width
|
Meter Mode
|
Max.Resolution
| 6,000 Counts
|
DMM Testing Modes
| Voltage, Current, Resistance, Capacitance,Diode & Continuity
|
Max. Input Voltage
| AC: 600V, DC: 800V
|
Max. Input Current
| AC: 10A, DC: 10A
|
Input Impedance
| 10 MΩ
|
Isolation
|
The float voltage between BNC and Ground
| 600V CATIII, 1000V CAT II
|
The float voltage between each Channel
| 600V CATIII, 1000V CAT II
|
The float voltage between Multimeter and Ground
| 1000V
|
between input Ports directly
| 400V CAT II
|
Input by 10:1 probe
| 600V CATIII, 1000V CAT II
|
The Max input voltage of Multimeter
| DC 800V,AC 600V
|
Display
|
Type
| Right angle 5.6 16-digit color LCD
|
Resolution
| 640*480 dots
|
Coast
| 16 gears, with the progress bar to show adjustment
|
Interface
| USB host and USB sle, Lan Optional
|
Power Supply
|
Voltage
| DC Input:12--17VDC, 2000mA
|
Mechanical
|
Size
| 245 x 163 x 52 (mm)
|
Weight
| 1.3KG (exclusive of packing and accessories)
|
